ClassicBond Sprayable Contact Bonding Adhesive

An alternative to standard bonding adhesive for membrane attachment to upstands and detailing. SPB adhesive is a spray applied, high-strength adhesive, formulated especially for gun application and bonding ClassicBond & ClassicBond Pro EPDM to a variety of substrates.

Suitable for a range of surfaces e.g. timber, brickwork, metal, PVC & concrete.

This tank does not come with the gun & hose. These can be found below.

Size:
14L (Coverage up to 60sq.m)
22L (Coverage up to 100 sqm)

Coverage: 0.17 Ltr / m2 when applied to both sides (depending on surfaces)

Advantages of traditional Contact Bonding Adhesive
Up to 6 times faster application time
Up to 4 times faster drying time
Increased operating window
Zero Waste Up to 100 square metres per cannister

Application Up-stands 
Spray the contact bonding adhesive onto the upstand and the back of the membrane from a distance of 100mm-150mm. It is also good practice to secure the membrane to the deck perimeter with a 150mm width strip of contact adhesive. Ensure that the contact adhesive is touch dry before rolling the membrane onto the substrate/up-stand.

Application Non-Permeable Deck
Spray the adhesive on to both the deck and underside of membrane evenly from an approximate distance of 100-150mm. Ensure that the contact adhesive is touch dry before rolling the membrane onto the deck. Note It is not possible to re-position the membrane once stuck down using contact adhesive.

Installation Tip
Allow sufficient time for the the contact adhesive to become touch dry dependant on weather conditions. If the membrane is bonded whilst the contact adhesive is still wet you may notice air bubbles appearing under the membrane. These will disappear within a short period of time due to the rubber roofing membrane being partially breathable.

ClassicBond Sprayable Contact Bonding Adhesive

An alternative to standard bonding adhesive for membrane attachment to upstands and detailing. SPB adhesive is a spray applied, high-strength adhesive, formulated especially for gun application and bonding ClassicBond & ClassicBond Pro EPDM to a variety of substrates.

Suitable for a range of surfaces e.g. timber, brickwork, metal, PVC & concrete.

This tank does not come with the gun & hose. These can be found below.

Size:
14L (Coverage up to 60sq.m)
22L (Coverage up to 100 sqm)

Coverage: 0.17 Ltr / m2 when applied to both sides (depending on surfaces)

Advantages of traditional Contact Bonding Adhesive
Up to 6 times faster application time
Up to 4 times faster drying time
Increased operating window
Zero Waste Up to 100 square metres per cannister

Application Up-stands 
Spray the contact bonding adhesive onto the upstand and the back of the membrane from a distance of 100mm-150mm. It is also good practice to secure the membrane to the deck perimeter with a 150mm width strip of contact adhesive. Ensure that the contact adhesive is touch dry before rolling the membrane onto the substrate/up-stand.

Application Non-Permeable Deck
Spray the adhesive on to both the deck and underside of membrane evenly from an approximate distance of 100-150mm. Ensure that the contact adhesive is touch dry before rolling the membrane onto the deck. Note It is not possible to re-position the membrane once stuck down using contact adhesive.

Installation Tip
Allow sufficient time for the the contact adhesive to become touch dry dependant on weather conditions. If the membrane is bonded whilst the contact adhesive is still wet you may notice air bubbles appearing under the membrane. These will disappear within a short period of time due to the rubber roofing membrane being partially breathable.

ClassicBond Sprayable Contact Bonding Adhesive

An alternative to standard bonding adhesive for membrane attachment to upstands and detailing. SPB adhesive is a spray applied, high-strength adhesive, formulated especially for gun application and bonding ClassicBond & ClassicBond Pro EPDM to a variety of substrates.

Suitable for a range of surfaces e.g. timber, brickwork, metal, PVC & concrete.

This tank does not come with the gun & hose. These can be found below.

Size:
14L (Coverage up to 60sq.m)
22L (Coverage up to 100 sqm)

Coverage: 0.17 Ltr / m2 when applied to both sides (depending on surfaces)

Advantages of traditional Contact Bonding Adhesive
Up to 6 times faster application time
Up to 4 times faster drying time
Increased operating window
Zero Waste Up to 100 square metres per cannister

Application Up-stands 
Spray the contact bonding adhesive onto the upstand and the back of the membrane from a distance of 100mm-150mm. It is also good practice to secure the membrane to the deck perimeter with a 150mm width strip of contact adhesive. Ensure that the contact adhesive is touch dry before rolling the membrane onto the substrate/up-stand.

Application Non-Permeable Deck
Spray the adhesive on to both the deck and underside of membrane evenly from an approximate distance of 100-150mm. Ensure that the contact adhesive is touch dry before rolling the membrane onto the deck. Note It is not possible to re-position the membrane once stuck down using contact adhesive.

Installation Tip
Allow sufficient time for the the contact adhesive to become touch dry dependant on weather conditions. If the membrane is bonded whilst the contact adhesive is still wet you may notice air bubbles appearing under the membrane. These will disappear within a short period of time due to the rubber roofing membrane being partially breathable.